
Gerotor Motor
Structure features: Axial Distribution structure and column stator and rotor design high mechanical efficiency; Special dynamic sealing ring design with high back pressure bearing capacity; Multiple installation forms of Flanges, output shafts, ports, and etc. Small volume, compact structure and light mass.
- Product Introduction
| cc/r Displacement, cc/r | 8 | 12.5 | 20 | 32 | 40 | 50 | |
| Flow, LPM | Cont. | 14 | 18 | 18 | 18 | 20 | 20 |
| Int. | 20 | 25 | 25 | 25 | 25 | 25 | |
| Speed, RPM | Cont. | 1537 | 1256 | 814 | 513 | 452 | 358 |
| Int. | 2450 | 1940 | 1250 | 800 | 630 | 500 | |
| Pressure, MPa | Cont. | 10 | 10 | 10 | 10 | 8.5 | 7 |
| Int. | 14 | 14 | 14 | 14 | 14 | 14 | |
| Torque, Nm | Cont. | 8 | 13 | 19 | 31 | 37 | 44 |
| Int. | 15 | 23 | 35 | 57 | 70 | 88 | |
Do not operate the motor at the Max. speed and the Max. pressure at the same time.
The motor operating time per minute must not exceed 10% under intermitent operating conditions.
Recommended oil: anti-wear hydraulic oil; Viscosity: 37-73cst; Oil cleanliness: 1S018/13.
The Max. oil temperature should be 80℃.
The series motor adopt special imported shaft seal assembly.The Max. allowable back pressure of the motor can be up to 10MPa; however, inorder to obtain the good service life and comprehensive mechanical performances, the back pressure should not exceed 5MPa. lf it is exceededit is recommended to connect the external drain pipe; when connecting the exteral drain pipe, ensure that the motor is aways fied with oi.wherconnecting the external drain pipe, in addition to maintaining a low back presure, the wear contaminants generated inside the motor can be removedand a certain cooling effect can be achieved.
There should be a running-in period before the motor is operated at fulload. t is recommended to run for th at 30% ofthe Max.operaing pressure.
Round flange|
Displacement, cc/r
|
8 | 12.5 | 20 | 32 | 40 | 50 |
|
L mm
|
108.8 | 110.8 | 113.8 | 118.8 | 122.8 | 126.8 |
|
Displacement, cc/r
|
8 | 12.5 | 20 | 32 | 40 | 50 |
|
L mm
|
105.5 | 107.5 |
110.5 |
115.5 | 119.5 | 123.5 |

|
Displacement, cc/r
|
8 | 12.5 | 20 | 32 | 40 | 50 |
|
L mm
|
108.8 | 110.8 | 113.8 | 118.8 | 122.8 | 126.8 |
|
Displacement, cc/r
|
8 | 12.5 | 20 | 32 | 40 | 50 |
|
L mm
|
105.5 | 107.5 |
110.5 |
115.5 | 119.5 | 123.5 |
Standard direction of rotation: when facing shaft end of motor, shaft to rotate clockwise when the oil is fed at port A and discharged at port B.

Hot Tags: gerotor motor, China gerotor motor manufacturers, factory, hydraulic motor french market, hydraulic motor north america market, hydraulic motor brazilian market, js series eaton orbit motor, hydraulic motor shafts, hydraulic motor networking








